Download FLUKE PM PM PM PM 2X2MV,MHZ OSCILLOSOPE SM service manual & repair info for electronics experts. Re: Fluke PM manual needed (MHz scope) The service manual for Fluke / Philips PM PM PM PM can be found. PM ). Deflection Manual positioning: Horizontal, Vertical, Both . Web access: com.
|Published (Last):||12 February 2018|
|PDF File Size:||16.60 Mb|
|ePub File Size:||6.74 Mb|
|Price:||Free* [*Free Regsitration Required]|
For the avoidance of doubt removal includes where applicable disconnection from the mains electricity supply and the detachment of any lots which are fixed.
I appreciate your wise input! Within 2 minutes the instrument automatically does its main calibrations. The error code lists are a usefull help in faultfinding; in many cases a displayed error code will point to the defective circuit part.
The Vendor shall only sell such title to the Goods as he may have.
Fluke PM3082 Service Manual
Apply a video signal to input CH1 with an amplitude of about 1V synchronization pulse At 10 MHz; input to deselected channel equivalent to 8 div. Bidding for any lot shall be deemed to be an acceptance of these conditions and any conditions in the Notices to Purchasers. There was an error sending your enquiry, why not try again later.
Input attenuators and calibrator. Anyway, it appears that I’ve got another nice looking four channel oscilloscope on my bench!
The knobs have an integrated shaft and fixing device. A brief examination of the primary side of the smps reveals no shorts. Type of instrument Required specification Your bid or registration is pending approval with the auctioneer. The unit A1 description is split into the following chapters: The purchaser should ensure that their contractors hold sufficient public liability insurance, copies of which should be made available to Lambert Smith Hampton if demanded.
In no circumstances will the Auctioneers or the Vendor be responsible if any Goods mannual part thereof be lost, stolen, damaged or destroyed after the Buyer is declared.
Input Characteristics Note 1: Like if he forgot to use the isolation transformer. We flu,e making things easier for you, auction specific shipping information coming soon. Adjust the input signal to an amplitude of exactly 6 divisions. The Auctioneers reserve the right to stop the removal of a lot by a Buyer, his agents or employees, if it appears to the Auctioneers or its agents or employees that the removal is being carried out in an unsafe or unsatisfactory way.
PM User Manual – PM Oscilloscope from Fluke
We will be pleased to advise accordingly. Refer to section 8. Page Verify that the deviation from the ideal straight line does not exceed 0. This eliminates calibration inaccuracies due to temperature changes. Properties expressed in numerical values without tolerances, ranges or limits stated, represent the characteristics of an average instrument.
That short may have blown open during the event, typically a copper track vaporises or a semi blows open. A second input signal ZT determines the intensity Z component of the text information.
Please note time changed to end from The digital multimeter and oscilloscope are not required for this test. Verify that a horizontal line of 4.
Put CH1 in 0. The option is factory-installable only. Cookies help us deliver our services.
FLUKE PM SERVICE MANUAL Pdf Download.
This delay is verified in the following test. Page bcc U p BCC: Each data block sent by the microprocessor is preceeded by an address on which the device can respond. The x1 is switched by control signal PA1X1. The output signal from the delay line is applied to the input pins 6 and 9 of amplifier IC D This gives a time-linear voltage across the capacitor; the so- called sawtooth or sweep signal.
Oscilloscope Fluke PM3082 powersupply problem?
Severability In the event that any provisions of these conditions shall be held unenforceable for any reason, the remaining conditions shall remain in full force and effect. Use desolder braided wire; ordering code: Here, the accuracy of this range is checked.
Before soldering, bend the wires through the holes of the solder leads, or wrap the wires around the leads in the form of an open U, or, maintain wiring ridigity by cable clamps or cable lacing. Dangerous Substances It is expressly brought to the attention of Buyers and potential buyers that certain types of plant or main service installations could contain blue and white asbestos, dangerous chemicals and hazardous waste which if not handled correctly during their removal from the premises could be in breach of the Health and Safety at Work ActSections Control of Substances Hazardous to Health Regulations COSHH or other current legislation regulating the use of such substances in a working environment.
Bidders are strongly advised to read them carefully. The input signal is a current and is applied to V and V Configuration of mmicroprocessor control part Page – Probe Adjust signal; frequency and outpu