WLAP repeater mode is WDS repeater, so it can connect other wireless device with MAC address. So you can set another station in Bridge mode. AirLive WLAP, WLAP is in conformity with. In accordance with 93/68/ EEC Directive and /5 EC-R & TTE Directive. Clause. Description. The WLAP and WLAP uses different firmwares. Please do not use the wrong firmware (i.e. do not use WLAP firmware on.
|Published (Last):||9 February 2009|
|PDF File Size:||12.33 Mb|
|ePub File Size:||3.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency airlivf and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Parts Names and Functions 1. Status Turns solid red when the device is booting, after boot successfully, the light turn off. Performing the Factory Reset will erase all previously entered device settings. Disabled IP Address Before you starting hardware connection, you are advised to find an appropriate location to place the Access Point.
Usually, the best place for the Access Airlivw is at the center of your wireless network, with line of straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is placed, the better will be the performance.
This device is shipped with configuration that is functional right out of the box. If you want to change the settings in order to perform more advanced configuration or even change the mode airrlive operation, you can use the web-based utility provided by the manufacturer as described in the following sections.
Refer to the illustration below.
Client Mode Ad-hoc If set to the Client Ad-hoc mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface. You can share files and printers between wireless stations PC and laptop with wireless network adapter installed. Users can use this feature to build up a large wireless airlivs in a large space like airports, hotels and schools …etc.
Wl-54500ap an Ethernet cable between your computer and the Wireless Access Point. Make sure your wired station is set wl-545ap the same subnet as the Wireless Access Point, i. In the Address box, enter the following: Status In this screen, you can see the current settings and status of this Access Point.
You can change settings by selecting specific tab described in below. System System Uptime The time period since the device was up. Firmware Version The current version of the firmware installed in this device. An SSID is also referred to as a network name because essentially wl-5450app is a name that identifies a wireless network. Channel Number The number of channels supported depends ajrlive the region of this Access Point. All stations communicating with the Access Point must use the same channel.
System manager can use the system log to trace when problems occur. Wireless Basic Settings This page includes all primary and major parameters.
Any parameter change will cause the device to reboot for the new settings to take effect.
It is case-sensitive and must not exceed 32 airliev. Advanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Authentication Type To provide a certain level of security, the IEEE Fragment Threshold Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network.
Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point.
Data Rate By default, the unit adaptively selects the highest possible rate for transmission. Security Here you can configure the security of your wireless network. Selecting airlibe method will enable you to have different level of security. Please note that by using any encryption, by which data packet is encrypted before transmission to prevent data packets from being eavesdropped by unrelated people, there may be a significant degradation of the data throughput on the wireless link.
The default is seconds. Preauthentication provides a way to establish a PMK security association before a client associates. If the list contains no entries with this function being enabled, then no clients will be able to access this Access Point. When you are in the client mode, you can select one AP to associate. Press Refresh to get the latest information. Two APs in bridge modes can communicate with each other through wireless interface.
Airlivd may enter up to 20 characters as a remark to the previous MAC Address. Apply Changes Press to save the new settings on the screen. Reset Press to discard the data you have entered since last time you press Apply Change.
If your system manager assigned you static IP settings, then you will have to enter the information provided. Infinite el-5450ap will happen in the network when WDS is enabled and there are multiple active air,ive between stations. Other Upgrade Firmware 1. Download the latest firmware from your distributor and save the file on the hard drive.
Start the browser, open the configuration page, click on Other, and click Upgrade Firmware to enter the Upgrade Firmware window. Save Settings to File: Load Settings From File: Password For secure reason, it is recommended that you set the account to access the web server of this Access Point.
Leaving the user name and password blank will disable the protection. The login screen prompts immediately once you finish setting the account and password. Remember your user name and password for you will be asked to enter them every time you access the web server of this Access Point. Page of 34 Go.
Table of Contents Add to my manuals Add. Table Of Contents Introduction Application Application Example 1 Example Client Mode ad-hoc Client Mode Ad-hoc If set to the Client Ad-hoc mode, this device can work like a wireless station when it is connected to a computer so that the computer can send packets from wired end to wireless interface. Status Status In this screen, aitlive can see the current settings and status of this Access Point.
Air Live WL-5450AP User Manual
Page 17 unique SSID. Wireless Wireless Basic Settings This page includes all primary and major parameters. Advanced Settings Advanced Settings It is not recommended that settings in this page to be changed unless advanced users want to change to meet their wireless environment for optimal performance Airlibe Type To provide a certain level of security, the IEEE Page 23 Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point.
Security Security Here you can configure the security of your wireless network. Airlivve 26 change automatically. Other Other Upgrade Firmware 1. Page 33 Save Settings to File: Password Password For secure reason, it is recommended that you set the account to sl-5450ap the web server of this Access Point.
This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only akrlive page. To print the manual completely, please, download it.
Download AirLive WLAP Access Point Firmware eu for OS Independent
Don’t show me this message again. Got it, continue to print. Don’t have an account?