AD009 03 PDF

Find the cheap Ad 03 Learning Remote Control Ic Chip, Find the best Ad 03 Learning Remote Control Ic Chip deals, Sourcing the right Ad AD datasheet, AD datasheets, AD pdf, AD price, AD buy, AD stock. ad learning remote control ic chip, Find Quality ad learning remote control ic chip and Buy ad learning remote control ic chip from Reliable.

Author: Vudozilkree Dubei
Country: Qatar
Language: English (Spanish)
Genre: Literature
Published (Last): 13 March 2015
Pages: 403
PDF File Size: 6.8 Mb
ePub File Size: 7.66 Mb
ISBN: 908-4-89604-326-2
Downloads: 49101
Price: Free* [*Free Regsitration Required]
Uploader: Gardajinn

Additionally, it provides one frequency programmable av009 duty selectable Pulse Width Modulation PWM output for remote control. And it provides a built-in capture mode timer for ad0009 signal frequency detecting by infrared learning function. It operates over a wide voltage range of 2. It pin with input with pull low or high resistor and output low multifunction. Two power saving modes: Low Voltage Reset 1. Timer mode with clock source selectable?

PWM output in carrier signal mode with duty and driver current 003 PWM output in ad0009 carrier signal mode with driver current programmable?

Capture the input signal frequency? Detect the signal envelop has a SLEEP mode for power saving which retains the contents of RAM, but stops the oscillator and causes all other chip functions to be inoperative.

SLEEP mode can be released by using external wakeup sources. Meanwhile, the built-in IR transfer module can make IR control and usage easily. Up to 8MHz clock operation Memories? Built-in IR RX can supply capture function with sensitivity adjustable. OTP Program power supply. Normal wakeup source, if key is changed, chip wakeup from sleep mode.

Key scan wakeup source, if key change is detected, chip wakeup from sleep mode. Key scan wakeup source, if key change is detected, chip wakes up from sleep mode. It will be connected with external crystal for a crystal oscillation circuitry in crystal mode. It is connected with external crystal for a crystal oscillation circuitry in crystal mode.

The power supply for SRAM block. Central Processing Unit 5. When subroutine call is executed or an interrupt occurrence is accepted, the value of stack point is updated automatically. The oscillation frequency could be varied up to 8.

Stack Pointer The CPU has an 8-bit-wide register indicating the location in the stack to be accessed push or pop when a subroutine call or interrupt occurs.

Fixed value by hardware 5. This register indicates the address of next instruction to be executed.

Status Register P The 8-bit status register contains the interrupt mask and 6 flags representative of the result of the instruction just executed. These bits can be individually controlled by specific instructions. Figure System registers The detailed description is shown in following description. Not all instructions affect status register. A detailed instruction description will be discussed in instruction manual.

  EL JUEGO SUPREMO ROPP PDF

Negative flag bit This flag indicates the bit7 status of the result of a data or arithmetic operation. Programmer can use this bit to do some operations, e. These register contents are added to the Some specified address, which becomes the actual address. Overflow flag bit This flag indicates whether the overflow has occurred in arithmetic operation.

Ad Learning Remote Control Ic Chip: China Suppliers –

The CPU has two operation modes; binary mode and decimal mode for arithmetic operation. Carry flag Interrupt disable flag This bit can enable or disable all interrupt except NMI interrupt source. In addition, some shift instructions or rotate instructions also change this bit. Programmer can use the Zero flag This flag indicates the result of a data or arithmetic operation. Contrary, this Figure Status register?

Program memory can be read only. It contains up to 8K bytes of program memory. Data memory that contains bytes of RAM including stack area can be read and written.

Configuration Register The configuration register is used to setup the operation condition. Crystal resonator or internal oscillator clock source option. LVR enable or disable option. Watchdog enable or disable option. Its RAM consists of xd009 including Stack.

The exception vectors should be specified in the program to have proper operation. Configuration Check bits must be filled in All of the control are not implemented on the chip.

Some of bits in control register are read only. When writing to them, there are no any effects on the corresponding bits. The following table shows the summary of the control registers. The detailed information of each control registers are explained in each peripheral section.

AD 03 AD 03T SOP 16 on | Alibaba Group

Some of the control registers ar009 control and status bits for peripheral module such as Timer unit, Interrupt control unit, etc. The detailed configuration register setting of device has been given in Section 5. Figure Two types of clock sources 5. Power Saving Mode 5.

These two modes are able to reduce power consumption and save power. They also feature qd009 wakeup time. Introduction GPM6PA provides eight types of interrupt sources with the same normal interrupt level. These interrupts have individual status occurred or not and control enable or not registers.

In a corresponding way, the system abstract the return PC address from the bottom of the stack when finished the interrupt service See Figure These interrupt sources are listed as [Table] and will be described in corresponding section. With any instruction, interrupts pending during the previous instruction is served.

If the related interrupt control bit is set to enable interrupt, an interrupt request signal will be generated and then CPU executes the interrupt service routine.

  CANON IXUS L1 PDF

If the related interrupt control bit is disabled, The interrupt flag bits programmer still can observe the corresponding flag bit, but no interrupt request signal will be generated. Envelope flag showing whether envelope exist or not. These reset sources can be concluded as external events and internal events. The internal events come from the program run away.

Figure shows the affected region for Figure Reset sources 5. After that, the system will operate in target speed and start to activate. If this function is enabled, the LVR circuit will monitor power level while chip is operating. This function prevents MCU from working at an invalid operating voltage range. This function prevents the MCU from being stuck in an abnormal condition. Different Reset Sequences as the following figures: These port pins may be multiplexed with an alternate function for the peripheral features on the device.

In general, when an initial reset state occurs, all ports are used as a general purpose input There are three parts, data, direction and attribution Each corresponding bit in these The setting rules are as follows: The direction setting determines whether this pin is an input or an output.

The data register is used to read the value on the port, which In M-Type keyboard application, Port B should be configured as input ports, and in sleep mode any change occurred in these ports will cause system wakeup.

Any of the keys touch would cause system wakeup. Port B Port B is a 6-bit programmable bi-directional port. Port B direction register. Port B Data value. Port B Key scan select register.

Port D Port D is a 6-bit programmable bi-directional port. Port D direction register. Port D Data value. Port D Key scan select register. Timer A contains one powerful PWM function function can be easily configured.

Cheap ad009 03 learning remote control ic chip deals

Timer A also has a capture function which can capture the frequency of input signal. And Timer A has another function is envelope detection; it can detect envelope waveform of input signal with or without carrier signal.

When Timer A is started, the value of 4-bit high-byte low-nibble register and 8-bit low-byte register would firstly be loaded into the bit counter and then the counter starts count up from the loaded value.

So the carrier signal with frequency programmable can be generated by this PWM mode via configuring these two registers. Timer A must generate carry clock at first, which is same as normal PWM generation. 003 enable Timer B and select Timer A carrier signal as its input clock.